AX360 Seamless Impact Cut 5 Gloves

$30.00

AX360 Seamless Impact Cut 5 Gloves

In stock
SKU AXIMPC5-06
Weight 1 lbs
Sizes S, M, L, XL, XXL
Colors Gray

Palm width in inches

Download Hand Sizing Guide

Small Size is
2 5/8" - 3 1/8"

Medium Size is
3 1/8" - 3 1/2"

Large Size is
3 1/2" - 3 15/16"

XL Size is
3 15/16" - 4 7/16""

2XL Size is
4 7/16" - 4 13/16"

3XL Size is
4 13/16" +

Glove Safety Features

Abrasion Resistant

Abrasion Resistant 4

Abrasion resistant is part of the mechanical risk tests in ANSI 105 and EN 388 for work glove performance requirements. The EN 388 is measured on a 1-4 scale (4 being the most abrasion resistant) and ANSI 105 is measured on a 0-6 scale (6 being the most abrasion resistant). The abrasion resistance test is done by rotating a flat surface against the glove palm material until it is punctured.

Cut Resistance

Cut Level 5

Cut Resistance is the most talked about attribute when it comes to hand safety. Gloves are measured on a 1-5 scale (5 being most cut resistant) by EN 388:2016 standards and a A1-A9 scale (9 being the most cut resistant) by ANSI/ISEA 105-2016 standards. The EN 388 rating may also include the results of the TDM-100 cut test, which are measured on an A-I scale (I being the most cut resistant). For more information on cut resistance, check out our cut resistance blog.

Dexterity

Dexterity Level 3

Dexterity is the tactile sensitivity (or flexibility) of a glove. In general, the thinner the glove, the more dexterity it has and the easier it will be to handle small objects. The test we use to determine 212 Performance glove dexterity is EN 420:2009. This test measures the smallest stainless steel pin that can be picked up. The smaller the object, the higher the rating on a 1-5 scale.

Impact Resistance

Impact Resistant

Impact resistance was recently added to the EN 388:2016 glove safety rating and measures back-of-hand knuckle impact protection. There are three potential ratings that would be included on the EN 388 safety icon: P for passed impact protection test, F for failed impact protection test, and X for not test for impact protection. There currently are no glove impact protection safety standards for ANSI/ISEA.

Puncture Resistance

Puncture Resistant 4

Glove puncture resistance is tested using the ANSI 105:2011 and EN 388:2016 standard, part of the mechanical risk tests. A blunt probe is pushed through the glove material until failure. For the EN 388, the ratings are based on a 1-4 scale (4 being the most puncture resistant), and for the ANSI 105, the ratings are based on a 0.

Tear Level

Tear Level 4

Tear resistance is the measurement of textile tinsel strength of the main material of a glove. EN388:2016 and ASTM D2261 are the two most frequently used tests to measure tear strength. They are both measured by clamping the material to two jaws and increasing the force separating the jaws until the material breaks. EN388:2016 is measured on a 1-4 scale (4 being the most tear resistant). ASTM D2261 is measured simply by reporting the force of the tear.

Blades a little sharper than you were expecting? Call in the cut 5. The AX360 IMPACT C5 is the ultimate cut protection glove. Offering extreme dexterity, cooling HPPE material, a foam nitrile grip and TPR back of hand protection, this glove can handle almost anything!

FEATURES

  • Heavy-Duty, Flexible Impact Knuckle Protection
  • EN Cut Level 5 Resistance
  • Foam Nitrile Palm for Enhanced Grip in Wet/Dry Conditions
  • HPPE Shell is Breathable and Keeps Hands Cool
  • Elastic Cuff Keeps Dirt and Debris out of Glove
  • Semi-Porous Palm to Channel Liquids
  • ANSI A3 Cut Resistance

WARNING! This product will melt when exposed to extreme heat or open flames, posing a risk of serious injury where melted product comes into contact with skin!

WARNING!: California residents only. Prop 65 warning.

Learn More.